Xebra Server Administraton - Revision history

Fabioz: Removing all content from page

2009-06-30T19:14:12Z

Removing all content from page

Fabioz at 18:56, 30 June 2009

2009-06-30T18:56:43Z

Fabioz: /* Modules */

2009-06-30T16:50:43Z

‎Modules

Fabioz at 16:46, 30 June 2009

2009-06-30T16:46:44Z

Fabioz: New page: =Modules= The server automatically launches the following modules: * mod_http: Listens to requests from the http plugin on the http_port that is specified in the config file. These request...

2009-06-30T16:45:24Z

New page: =Modules= The server automatically launches the following modules: * mod_http: Listens to requests from the http plugin on the http_port that is specified in the config file. These request...

New page

=Modules=
The server automatically launches the following modules:
* mod_http: Listens to requests from the http plugin on the http_port that is specified in the config file. These request are forwarded to the appropriate webapp.
* mod_console: Reads input from the console. The commands described below can be invoked.
* mod_cmd: Listens to command request from the webapps on the cmd_port that is specified in the config file.

=Webapps=

==Assume webapps are running==
If assume_webapps_are_running was set, the server does not translate, compile and run the webapps. It just tries to connect immediately. This should be used when a webapp is launched in estudio for debugging and the server should not try to run and shutdown the webapp.

==Development Mode==
By default, a webapp is set to Development Mode which means that the server checks everytime a request was made if the webapp needs to be retranslated and compiled. This makes access to the webapp very slow. As soon as development of the webapp stopps, dev_mod should be set to off.

==Fire off a webapp==
If the server crashed and therefore could not properly shut down all webapps, they will still be running when the server is relaunched. Hence, the socket will be occupied when the server tries to launch a webapp. Use the fire command to fire off a possibly running webapp. The fire command tries to directly connect to the webapp and send a shutdown signal regardless if the webapp process is owned by the server or not.

=Config File=
* see [[Xebra Server Config File]]

=Run Arguments=

<code>
USAGE:
xebra_server <config_filename> [-d <debug_level>] [-c] [-r] [-v]

OPTIONS:
-d --debug_level : Specifies a debug level. 0: No debug output. 10: All debug ouput. (Optional)
-c --clean : If set, all webapps will be cleaned (Optional)
-r --assume_webapps_are_running: If set, the server assumes that the webapps are already running and does not
translate, compile and run them before connect to them. (Optional)
-h --help : Display usage information. (Optional)
-v --version : Displays version information. (Optional)

ARGUMENTS:
<debug_level>: The debug level (0-10)

NON-SWITCHED ARGUMENTS:
<config_filename>: The path of the config.ini file to use.
</code>

=Console Commands=

==General==
* 'help': Displays a list of commands.

==Webapps==
* 'clean <name>': Cleans, re-translates, compiles and launches a webapp.
* 'dev <name>': Sets developing mode of a webapp to on.
* 'dev_all': Sets dev_mod to on on all webapps.
* 'dev_off <name>': Sets developing mode of a webapp to off.
* 'dev_off_all': Sets dev_mod to off on all webapps.
* 'dev_on <name>': Sets developing mode of a webapp to on.
* 'disable <name>': Disables a webapp.
* 'enable <name>': Enables a webapp.
* 'fire <name>': Sends shutdown signal to webapp.
* 'get_sessions': Retrieves the number of sessions of all running webapps.
* 'shutdown <name>': Shuts down a webapp.
* 'translate <name>': Forces re-translation of webapp.
* 'webapps': Displays the available webapps.

==Server Control==
* 'exit': Shuts down the server.
* 'reload': Reloads the server configuration file.
* 'shutdown_webapps': Shuts down all webapps.

==Modules==
* 'mlaunch <name>': Re-launches a server module.
* 'modules': Displays the available modules.
* 'mshutdown <name>': Shuts down a server module.

← Older revision		Revision as of 19:14, 30 June 2009
Line 1:		Line 1:
−	~~[[Category:Xebra]]~~

−	~~=Modules=~~
−	~~The server automatically launches the following modules:~~
−	* mod_http: Listens to requests from the http plugin (Apache Module or IIS7 Handler) on port 55001. These request are forwarded to the appropriate webapp.
−	* mod_console: Reads input from the console. The commands described below can be invoked.
−	* mod_cmd: Listens to command request from the webapps on port 55002.
−
−	~~=Webapps=~~
−
−	~~==Assume webapps are running==~~
−	If assume_webapps_are_running was set, the server does not translate, compile and run the webapps. It just tries to connect immediately. This should be used when a webapp is launched in estudio for debugging and the server should not try to run and shutdown the webapp.
−
−	~~==Development Mode==~~
−	By default, a webapp is set to Development Mode which means that the server checks everytime a request was made if the webapp needs to be retranslated and compiled. This makes access to the webapp very slow. As soon as development of the webapp stopps, dev_mod should be set to off.
−
−	~~==Fire off a webapp==~~
−	If the server crashed and therefore could not properly shut down all webapps, they will still be running when the server is relaunched. Hence, the socket will be occupied when the server tries to launch a webapp. Use the fire command to fire off a possibly running webapp. The fire command tries to directly connect to the webapp and send a shutdown signal regardless if the webapp process is owned by the server or not.
−
−
−
−	~~=Config File=~~
−	* see [[Xebra Server Config File]]
−
−	~~=Run Arguments=~~
−
−	~~<code>~~
−	~~USAGE:~~
−	~~xebra_server <config_filename> [-d <debug_level>] [-c] [-r] [-v]~~
−
−	~~OPTIONS:~~
−	~~-d --debug_level : Specifies a debug level. 0: No debug output. 10: All debug ouput. (Optional)~~
−	~~-c --clean : If set, all webapps will be cleaned (Optional)~~
−	~~-r --assume_webapps_are_running: If set, the server assumes that the webapps are already running and does not~~
−	~~translate, compile and run them before connect to them. (Optional)~~
−	~~-h --help : Display usage information. (Optional)~~
−	~~-v --version : Displays version information. (Optional)~~
−
−	~~ARGUMENTS:~~
−	~~<debug_level>: The debug level (0-10)~~
−
−	~~NON-SWITCHED ARGUMENTS:~~
−	~~<config_filename>: The path of the config.ini file to use.~~
−	~~</code>~~
−
−	~~=Console Commands=~~
−
−	~~==General==~~
−	* 'help': Displays a list of commands.
−
−	~~==Webapps==~~
−	* 'clean <name>': Cleans, re-translates, compiles and launches a webapp.
−	* 'dev <name>': Sets developing mode of a webapp to on.
−	* 'dev_all': Sets dev_mod to on on all webapps.
−	* 'dev_off <name>': Sets developing mode of a webapp to off.
−	* 'dev_off_all': Sets dev_mod to off on all webapps.
−	* 'dev_on <name>': Sets developing mode of a webapp to on.
−	* 'disable <name>': Disables a webapp.
−	* 'enable <name>': Enables a webapp.
−	* 'fire <name>': Sends shutdown signal to webapp.
−	* 'get_sessions': Retrieves the number of sessions of all running webapps.
−	* 'shutdown <name>': Shuts down a webapp.
−	* 'translate <name>': Forces re-translation of webapp.
−	* 'webapps': Displays the available webapps.
−
−	~~==Server Control==~~
−	* 'exit': Shuts down the server.
−	* 'reload': Reloads the server configuration file.
−	* 'shutdown_webapps': Shuts down all webapps.
−
−	~~==Modules==~~
−	* 'mlaunch <name>': Re-launches a server module.
−	* 'modules': Displays the available modules.
−	* 'mshutdown <name>': Shuts down a server module.
−
−	~~=Webapp/Server Communication Protocol=~~
−	* [[Xebra Communication Protocol]]

← Older revision		Revision as of 18:56, 30 June 2009
Line 73:		Line 73:
	* 'modules': Displays the available modules.		* 'modules': Displays the available modules.
	* 'mshutdown <name>': Shuts down a server module.		* 'mshutdown <name>': Shuts down a server module.
		+
		+	=Webapp/Server Communication Protocol=
		+	* [[Xebra Communication Protocol]]

← Older revision		Revision as of 16:46, 30 June 2009
Line 1:		Line 1:
		+	[[Category:Xebra]]
		+
	=Modules=		=Modules=
	The server automatically launches the following modules:		The server automatically launches the following modules:

@@ Line 3: / Line 3: @@
 =Modules=
 The server automatically launches the following modules:
-* mod_http: Listens to requests from the http plugin on the http_port that is specified in the config file. These request are forwarded to the appropriate webapp.
+* mod_http: Listens to requests from the http plugin (Apache Module or IIS7 Handler) on port 55001. These request are forwarded to the appropriate webapp.
 * mod_console: Reads input from the console. The commands described below can be invoked.
-* mod_cmd: Listens to command request from the webapps on the cmd_port that is specified in the config file.
+* mod_cmd: Listens to command request from the webapps on port 55002.
 =Webapps=